According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
How long does it take to replace a ballast?
The ballast takes in electricity and then regulates current to the bulbs. A typical ballast will generally last about 20 years, but cold environments and bad bulbs can decrease this lifespan significantly. You can get a new ballast at a hardware store or home center and install it in about 10 minutes.
Is it worth replacing ballast in fluorescent light?
If your lights flicker or turn themselves off—and you’re sure it’s not due to bad tubes or bad sockets—it’s time to replace the ballast. Be sure to find a replacement ballast with the same wiring configuration and voltage rating as the original.
How can you tell if the ballast is bad?
One probe of the multimeter should touch the hot wire connections, while the other touches the neutral wire connections. If the ballast is good, an analog multimeter has a needle that will sweep to the right across the measuring scale. If the ballast is bad, then the needle won’t move.
Why do ballasts fail?
Ballast failure is often caused by the surrounding environment—mainly heat and moisture. When it’s too hot or too cold, a ballast can burn or fail to start your lamps. Heat, along with continuous condensation inside an electronic ballast, can cause corrosion over time.
Can a ballast catch fire?
As with any electrical situation where overheating is possible, a bad ballast can pose a fire danger. The overheated ballast could cause the plastic housing on the light itself to melt and, in the right conditions, flame up.
Do I need a new ballast?
Sometimes you have to crack the ballast open to see internal damage. If you see burn marks inside the device or on wires, replace it. It couldn’t handle the current and overloaded. If this is the case, you may need to replace your bulbs too.
Why do fluorescent bulbs flicker?
Without a properly operating ballast to limit the light’s current, a fluorescent lamp connected to the electrical source would quickly and uncontrollably increase its current flow—causing the lamp to burning out. This is why a degrading ballast will cause the fluorescent lights to flicker.
How much does it cost to convert fluorescent lights to LED?
On average, an electrician charges $50-$100 an hour. Once the value of the electrician is added to the value of the LED conversion kit and LED bulb, the cost can be a bit high with an all-around amount of about $160-$506.
Can a fluorescent light work without a ballast?
In a fluorescent lighting system, the ballast regulates the current to the lamps and provides sufficient voltage to start the lamps. Without a ballast to limit its current, a fluorescent lamp connected directly to a high voltage power source would rapidly and uncontrollably increase its current draw.
Does a bad ballast burn out bulbs?
The ballast itself can go bad, which causes lights to flicker or even appear to be burnt out, when in fact they aren’t. They require maintenance and energy to power, on top of the power used to light the fluorescent bulb. They are a large part of the equation when using fluorescent lamps.
Why does my fluorescent light work sometimes?
If a fluorescent tube blinks on and off-a slower and more distinct process than flickering-the fault may lie in loose wiring or in another component, called the ballast. The ballast is almost always to blame if the fixture hums during operation.
Do LED lights need a ballast?
No LED bulbs require a ballast, although some are engineered to work with an existing ballast. You will find ballast-compatible or “plug-and-play” LEDs that are designed to replace linear fluorescents, compact fluorescents, or HIDs. Incandescent and halogen lamps do not require a ballast.
How do I know if my ballast is T8 or T12?
If no markings are available, the size in diameter of the tube is the easiest way to determine the type you have installed. T8 tubes are 1-inch in diameter and T12 tubes are 1 1/2 -inch.
Will LED lights work with bad ballast?
Can LED lamps work off of existing ballasts? Yes, if they have an internal driver than can work off that ballast. Philips, for example, has designed a tube that is compatible with an existing electronic ballast.
How long do fluorescent bulbs last?
Typical lamp life for a fluorescent bulb is about 20,000 hours, but this can degrade as a consequence of frequent switching (turning on and off). Burning life is extended if lamps remain on continuously for long periods of time.
Why is my fluorescent light orange?
A mere spot or blotch or ring / band at one end or both ends is usually not a sign of end-of-life. Bulb Is Out or Very Dim and Ends Glow Dim Orange: Bulb is dead and a rapid start or trigger start ballast is making the filaments hot enough to visibly glow. Replace the bulb.
