The F31 error code means that the control board detects the oven temperature probe circuit is shorted. I have included a link below on how to test the sensor, and a link to the oven sensor for your model range. If the sensor tests good, then you could have a bad control board or a short in the wiring.
What does it mean when a Kenmore oven says F31?
The F31 error code indicates a shorted oven temperature sensor probe connection. You will need to check the probe connections. The oven temperature sensor probe pokes through the back wall of the oven at the top of the back panel.
How do you reset a Frigidaire oven?
Frigidaire Oven Error Codes
But the first thing you should do is try to perform a hard reset by unplugging the oven, waiting about 30 seconds, and then plugging it back in again. In some cases, this will be enough to reset the control board and get your oven working again.
What is an EOC on a Frigidaire oven?
An EOC, or electronic oven control, is a circuit board that works to control certain mechanical elements on stovetop ovens. Through a series of buttons, the board sends voltage to the oven’s igniter, which triggers the heating elements that either bake or broil your food.
How do you remove the error code on a Frigidaire stove?
It means when a key on the keypad has been detected as pressed in for a long time the F11 error is reported and all oven commands are terminated. First simply press the cancel key to clear the code. The error may have been caused by just holding down a key too long by mistake.
How do I fix the F2 code on my Whirlpool stove?
F2-E1 – Touch Pad (Keypad) Cable Unplugged – Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the ‘cancel’ function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.
Where is the oven temperature sensor for Kenmore oven?
The temperature sensor regulates oven temperature in modern ranges, like a thermostat. It is on the back wall near the broiler on the top wall.
How do I fix the F11 code on my Kenmore stove?
The “F11” fault code indicates a Shorted Keypad. Disconnect power to the range, For 10-20 minutes and reapply power. If “F11” returns upon power-up, replace the Electronic Oven Control (EOC). If you do not feel comfortable replacing the EOC, I recommend calling a service technician to diagnose and repair your range.
Why is my Kenmore stove beeping F10?
The F10 code on a Kenmore oven means that the oven is overheating — the oven is detecting a temperature far over the safe range of operation. Most models also start beeping when this happens since it can be a safety concern.
Is there a reset button on a Frigidaire oven?
You can reset your Frigidaire oven’s bake, broil, or roast modes simply by pressing “Cancel” button (some models). Also, you can try this option if you want to reset cooking time for your food.
How do I reset my oven control board?
Turn the circuit breaker to the OFF position or remove the fuse. Wait one minute, then turn the circuit breaker back to the ON position or install the fuse to reset power to the unit. This should reset the electronic controls on the range or wall oven.
How do you reset a Frigidaire oven door lock?
How do I Fix a Locked Frigidaire Gallery Oven?
Locate the oven lockout pad. The pad is located to the lower left of the clock and display screen. Press and hold the oven lockout pad. You will need to hold the pad down for 3 seconds. Wait.
How do I know if my oven temperature sensor is bad?
Symptoms of A Bad Oven Temperature Sensor
Longer Than Usual Cooking Times. Undercooked Foods. Uneven Cook on Your Meals. Overheating Issue. Solving the Problem With a Troubleshooting Tip. Trying out an Ohmmeter. Discovering a Combination of Problems. The Oven-Board Failure.
How much does it cost to replace an oven temperature sensor?
At the low end, replacing a temperature sensor would likely cost around $180 to $200. The most expensive repairs involve control board or control panel replacement. Sometimes, both the control panel and the electronic control board need replacing at the same time. That type of repair would likely cost around $1000.
Why does my oven not maintain temperature?
Faulty Electrical Connection
In all honesty, a faulty thermostat or heating element in your oven are the most likely culprits when your oven can’t maintain its temperature. As such, they should be checked first.
